Why Is My Car’s Engine Burning Oil?Posted by Amsoil, 22nd May 2018

The simple answer: 

It’s probably wearing out. Over time, the piston rings have likely become worn or stuck in grooves, preventing them from sealing tightly against the cylinder wall. 

The tiny gap that has formed between the ring and cylinder wall allows oil to enter the combustion chamber and burn. Worn valve seals produce the same effect. You may also be using an oil with poor resistance to heat, causing the oil to evaporate.

Buy AMSOIL in the UK

The detailed answer: 

Engines can burn oil due to a few reasons.

• Worn or stuck piston rings
• Worn valve seals
• Unstable motor oil
• Excessively low oil viscosity

Most car engine pistons contain three rings. The top and second rings are responsible for pressing tightly against the cylinder wall and sealing the combustion chamber, keeping combustion gases in and oil out. The oil ring scrapes oil off the cylinder wall on the way down the cylinder, depositing it back into the oil sump. Because an extremely thin film of oil lubricates the ring/cylinder wall interface, it is normal for some oil to burn during combustion. What constitutes “normal” oil consumption, however, depends on the engine.

Valve seals also help prevent oil from entering the combustion chamber. Because oil is present to lubricate the seals and keep them pliable, some oil will burn during combustion. Even so, newer engines shouldn’t burn much oil. In fact, you shouldn’t need to add much – if any – top-off oil between oil changes, particularly if you’re using a high-quality fully synthetic oil. But be sure to check your oil regularly just in case.

Buy AMSOIL in Norway

Blame it on friction

Despite our best efforts, things eventually wear out, including engines. Worn rings can allow a gap to form between the ring face and cylinder wall. During operation, oil can slip past the rings into the combustion chamber, where it burns. Worn valve seals also contribute to engine burning oil.

Stuck rings, due to heavy deposits, can result in the same scenario. Using a conventional oil that fails to resist chemical breakdown can lead to ring-land deposits, which cause the rings to stick. When this happens, the piston rings no longer float in the cylinder liner and can lead to increased engine oil consumption (in addition to wear).

Buy AMSOIL in Finland

Where did the oil go?

You may also be using a motor oil with poor heat resistance. Conventional motor oils contain light, unstable molecules that more easily lift out of the solution in the presence of high heat, much like the heat of the sun lifts water molecules out of a puddle. As a result, the oil level drops as the oil is converted to carbon deposits throughout your engine.

This is likely what happened with my Oldsmobile Intrigue back in the dark ages before I started working at AMSOIL. I used a cheap oil from a discount retailer and scratched my head in befuddlement each time the oil on the dipstick registered low. I even went to a garage to check for oil leaks (he found none).

Buy AMSOIL Synthetic Oil

Use the correct viscosity of oil

Another possibility, albeit less likely, is you’re not using the correct viscosity of motor oil for your engine. Viscosity is defined as resistance to flow, but it’s easier to think of it as thickness. The lower the viscosity, the thinner the oil. As you can imagine, thinner oil will slip past worn rings or valve seals easier than thicker oil.

The correct oil viscosity for your engine is probably printed on the oil filler cap. If not, you can find it in the owner’s manual or contact your local AMSOIL distributors.

Some manufacturers recommend a range of viscosities depending on the temperature (e.g. 5W-20 when it’s cold, 10W-30 when it’s above 0ºC).

Using the highest recommended viscosity can help close the gap between the rings and cylinder bore, reducing engine oil consumption.

To fight engine from burning oil, use an oil that fights wear and deposits

The best way to prevent engine oil consumption is to use a high-quality fully synthetic oil that offers excellent wear protection and deposit resistance. Over time, the oil helps protect the piston rings from wearing out, so they continue to form a tight seal against the cylinder wall. Fully synthetic oil will also fight deposits that lead to ring sticking better than conventional oils.

Where to buy AMSOIL


Back to blog

Next post


I accept AMSOIL Privacy Policy

Thank you! Your email address has been registered.

About cookies on our website

We use cookies to give you the best experience on our site. By continuing to browse, you are agreeing to their use. Read more...